I’ve been thrilled to see all of the fabulous versions of Squiggles that you all are making. Some of you have already finished, others have made more than one version, while others are just beginning. Just remember – I’ll leave the blog posts up indefinitely, so you can make this fun quilt on your own schedule!
Step by Step Binding Tutorial
This is the same method I use for all of my quilts.
Step 1: Trim the Quilt
Trim the extra batting and backing flush with the edge of the quilt top.
I like to use a large square ruler for the corners, and a long acrylic ruler for the sides.
Step 2 – Make the Binding
Lay out two binding strips so that they overlap at a 90 degree angle. Mark a diagonal line on the top strip from corner to corner, where the corners overlap. Pin in place if needed.
To figure out how many binding strips you need to cut, add 10″ to the perimeter of the quilt (length of all 4 sides of the quilt). Then divide that number by 40″ to get the number of strips to cut. For the Squiggles quilt, the number of strips to cut is listed on page 15 of the book.
Tip: most patterns suggest to cut the binding strips 2 1/4″ to 2 1/2″ wide. However, I’ve recently began using 2″ strips and I like it much better. The narrower strips allow me to get a tighter finish, and both sides of the binding end up the same size.
Sew on the drawn line and trim excess to 1/4″. Trim off the “dog ears” – the triangle tips, too. Join all of the strips the same way and press seams open. This will distribute the bulk of the seam when it’s attached to the quilt.
Trim the beginning of the binding strip at a a 45 degree angle and press the entire length of binding in half, wrong sides together. Be sure to trim the starting edge first, before you press it in half.
If desired, fold up the binding, or roll it up until it’s ready to attach to the quilt.
Step 3 – Attach the Binding to the Quilt
Start attaching the binding on the side of the quilt, not at the corners. Line up the open edges of the binding to the trimmed edge of the quilt and leave about 8″-10″ of the tail hanging off. This will allow plenty of room for attaching the two ends later.
Place a pin in the binding and quickly “walk” it around the quilt’s perimeter to ensure that none of the pieced seams will land in the corners. Adjust the binding as needed and start sewing at the pin, using 1/4″ seams.
When you reach the corner, stop sewing 1/4″ away from the corner. Mark a line if needed to get an exact measurement. Then sew off the side or corner of the quilt.
To get a perfect miter in the corners, fold the binding up and away from the corner. Ensure that the right side of the binding aligns with the edge of the quilt.
Fold the binding back down, leaving the excess in the corner. Make sure the top of the fold lines up evenly with the top edge of the quilt. I called this the “funky fold.”
Grasp the top and bobbin threads and carefully sew down the next side of the binding. It will be thick at the corner where all of the bulk is.
Once you sew a little ways, check the front of the quilt. It should form a nice crisp miter at the corner if you’ve lined everything up correctly.
Continue sewing down all 4 sides of the binding, taking care to get nice crisp miters at the corners. When you get close to the starting point, leave several inches between the starting and ending point of the binding, so you have room to attach the two ends of the binding.
Step 4 – Secure the Ends
Open up the end of the binding and place the start of the binding (the angled cut end) on top of it. Be careful that the strips don’t shift.
Open up the beginning binding “tail” (below), and notice that the angled end runs in the opposite diagonal direction in which it was folded. Mark a line on the uncut strip, following the direction of the cut end.
Measure and cut 1/2″ away from the marked line. This will add the amount needed for seam allowances on both ends of the binding.
Match up the binding right sides together and make sure it doesn’t get twisted. Pin the binding, offsetting the triangle tips by about 1/4″ and sew with 1/4″ seams to close the binding. This will create a hidden join that is smooth, with no bumps.
Finger press this final seam open (it’s hard to get an iron in there at this point), and pin the un-sewn binding to the quilt, easing in any fullness. Attach this last bit of binding to the quilt, overlapping the starting and ending stitches.
If desired, press the binding away from the quilt with a hot dry, iron. This will help the binding wrap around to the back of the quilt much easier.
Secure the binding to the back of the quilt with pins or binding clips. When you get to the corners, fold them in opposite directions and clip in place.
Finish with small hand stitches on the back side. I use a single 16″ – 18″ length of Aurifil thread in a color that matches the binding. I use a thimble to push the needle through and sew from right to left, with the bulk of the quilt away from me. I’ve noticed that some quilters prefer to sew the oppoiste direction with the quilt toward them, and that’s okay, too – whatever works for you!
Of course, you can finish the binding by machine if you prefer, but I love the slow pace of hand stitching while I relax and cuddle with the quilt.
Here’s a quick bonus video of me hand-stitching the binding on another quilt:
Step 5 – Share, Share Share!
I hope you enjoyed this tutorial! You are welcome to share on pinterest or your favorite social media (with attribution). I hope that binding doesn’t seem so scary and feel free to mix it up with your favorite binding method.
This concludes the quilt along tutorials – next week I’ll share some finished pics of Squiggles, taken in the desert behind my neighborhood. Be sure and share your progress and finishes with me on instagram #squigglesqal or in my ChristaQuilts Facebook group. I love seeing them!!
Click here to get an autographed copy of Piece and Quilt with Precuts.
Click here for links to all of the Squiggles Quilt Along blog posts.